Figure 7-25

Encode

Encode setup includes the following items. See Figure 7-26. Here you can select

Channel: Here is for you to select a channel.

Channel name: Modify channel name.

Data stream: Regular and extra data stream.

AV enable: Video/Audio. System only displays video by default. You need to

manually enable audio function. Bit rate: There are two options: CBR and VBR. You can only set video quality in

VBR mode.

Frame rate: The value ranges from 1f/s to 25f/s (PAL) and 1f/s to 30f/s (NTSC). Compression: There are two options: H.264 and MPEG 4. Resolution: D1/HD1/DCIF/CIF

Quality: The value ranges from 1 to 6. The level 6 is the best video quality.

Figure 7-26

Schedule

Schedule includes the following interface. See Figure 7-27.

When DVR boots up, it is in 24-hour continuous record. In this interface you can set record type, record time and period. Record type includes regular record(R), motion detection record (M) and alarm record (A).

Channel: select the channel number you desire.

Week: you can select from the dropdown list. Or you can select at the bottom of the interface.

Prerecord: system can record the three to five seconds video before activating the record operation into the file.(Depends on data size) Period: There are six periods for you to set. Please click set button of the corresponding period. See Figure 7-28.Please note all the setup here shall be in one day. E.g. 00.00 to 24.00.

Figure 7-27

Figure 7-28

Tip:

After you finished setup for one channel, you can click save as button, system pops up the following interface. See Figure 7-29.Now you can copy one channel setup to other channels.

Figure 7-29

Network

Network interface is shown as in Figure 7-30. This interface includes the following items:

Max: Here you can set max connection amount. The value ranges from 0 to 10. 0 means no network connection is allowed.

TCP port: default setup is 37777. Please note port 37778 is for network UDP port use only.

HTTP port: default setup is 80.

Transfer: here you can select the priority between fluency/video quality. Enable PPPoE

In remote item, enable PPPoE function and then input PPPoE name and PPPoE

password you get from your ISP (Internet service provider). See Figure 7-30.

Click save button, you need to restart to activate your configuration.

After rebooting, DVR will connect to internet automatically. The IP displayed in the IP

address item is the dynamic value. You can use client-end software to visit current IP

now.

Enable DDNS

You need a PC of fixed IP in the internet and there is the DDNS software running in this PC. In other words, this PC is a DNS (domain name server).see Figure 7-31.

Please enable DDNS function and then input PC IP. Click save button and then

reboot device. Now you can login via DDNS. Please open IE and then input http:

(DDNS server IP)/ DDNServer / default.htm. for example, input http:

10.5.2.149/DDNServer/default.htm, you open a DDNS server web page.

Figure 7-31

RS232

RS232 includes the following items. See Figure 7-32.

Function: There are various devices for you to select. Console is for serial port or min-end platform to upgrade program. Keyboard is for you to use special keyboard to control current device.

Baud rate: Please select as you desire.

Data bit: The value ranges from 5 to 8.

Stop bit: There are three options: 1/1.5/2.

Parity: There are three options: none/odd /even.

Figure 7-32

Mul-DDNS

Here you can select DDNS type. This operation needs DVR device supported. See Figure 7-33.

FTP

After you completed setup here, system upload scheduled data to the specified FTP server regularly. Need device supported.

In Figure 7-34, you need to input FTP server address, port, log in user name and password. Then you need to specify the destination directory to save files.

File: here you can input uploaded file length (Unit: MB) if the file is smaller than the setup value here, system upload the whole file. If the file is larger than the setup value, system only uploads the setup value data and ignores the rest data.

Interval: for one channel of the same record type if there is more than one alarm, system only uploads the first file. For example, if the interval is five minutes, then system only uploads the first alarm or motion detection file even though there are several alarms in these five minutes. If the setup is 0, then system upload all files.

Time period: Click set button, you can an interface as in Figure 7-35. You can check the box to select the file type. System supports multiple choices.

Figure 7-34

Figure 7-35

Alarm

Please note before alarm setup, you need to properly connect alarm input and output device, send address and receive address. Click save button confirm current setup. Alarm setup includes the following items. See Figure 7-36.

Event Type: you can select event type from the drop down list: Local alarm/Net alarm.

Alarm in: Select corresponding alarm in channel

Type: There are two options: normal open and normal close.

Record channel: select record channel when alarm occurs. Please note you

need to select alarm record in DVR schedule interface and enable schedule

function in manual record interface.

Alarm output: select alarm activation channel when alarm occurs. Please note channel 3 is to control +12V output.

Show message: System can pop up a message to alarm you in the local host screen if you enabled this function.

Email: System can send out email to alert you when alarm occurs. PTZ activation: Here you can set PTZ movement when alarm occurs. Such as go to preset x when there is an alarm. Click set button, the interface is shown as in Figure 7-37.

Tour: Here you can enable tour function when alarm occurs. System supports multiple-window tour. Please go to chapter 5.3.9 Display for tour interval setup.

Figure 7-36

Figure 7-37

Detect

Detect interface is shown as in Figure 7-38. Here includes the following items:

Channel: Select channel name from the dropdown list. Type: There are three types: motion detection/Video loss/Camera mask detection.

Record channel: Here you can select record channel (Multiple choices). Please make sure you have set MD record in encode interface(Main Menu->Setting->Schedule) and schedule record in manual record interface(Main Menu->Advanced->Manual Record)

Period: Here is for you to set record period. Click set button, you can see an interface is shown as in Figure 7-39. In Figure 7-39, click time set button, you can see an interface is shown as in Figure 7-40. Here you can set time period. Sensitivity: There are six levels. The sixth level has the highest sensitivity. Region: If you select motion detection type, you can click this button to set motion detection zone. The interface is shown as in Figure 7-41. There are 192 zones (16*12). Right click mouse you can go to full-screen display mode. Do remember clicking OK button in Figure 7-41 to save your motion detection zone setup.

Alarm output: Here you can select activated external peripheral device when alarm occurs.

Show message. System can alert you on the local screen if you enabled this function.

Mail: system can send out email to alert you when alarm occurs. Tour: Here you can enable tour function when alarm occurs in corresponding channel. System supports multiple-window tour. Please go to chapter 5.3.9 Display for tour interval setup.

PTZ activation: Click set button, you can see an interface is shown as in Figure 7-42. System can go to corresponding preset when alarm occurs.

Figure 7-38